航天器运输包装箱仿真验证平台技术研究

针对数量有限的物理跑车试验无法满足减振与保温性能测试需求的问题，提出一套航天器运输包装箱动力学与热学仿真验证方法，包括：建立适用于包装箱系统的刚柔耦合多体动力学系统，通过结合线路条件测试生成的动力学系统外部激励，实现减振性能虚拟跑车测试；建立基于计算流体力学的包装箱热学模型，通过模拟自然对流和空调控制，实现包装箱保温性能虚拟跑车测试；基于C/S架构和导航式流程设计思想，建立航天器运输包装箱仿真验证平台，通过实际案例证明该平台仿真结果与实际跑车测试数据具有较高的一致性。     

天基轻气炮发射清除低轨碎片方案及关键技术分析

文章分析了现有的空间碎片清除方式,并以800~1200 km低地球轨道高度上1~10 cm量级的空间碎片为清除目标,提出了天基轻气炮清除碎片的新方法。首先分析了轻气炮有效载荷在典型参数下的弹丸加速能力;之后根据将碎片降轨使其坠入大气层烧毁的设想,提出天基轻气炮共面清除碎片的方式,并选择轨道高度800 km的圆轨道作为碎片运行轨道进行可行性分析。计算表明,对半径10 cm、厚度1 cm的铝合金圆板碎片(质量211.95 g),使用初速1 km/s、重10 g的黏性弹丸可按任务方案达到清除效果。此外,计算出该参数弹丸对轨道高度800~1200 km的圆轨道上可清除的最大碎片质量为500~825 g,证明轻气炮弹丸对1~10 cm的碎片具有较强的清除能力。最后,分析了以轻气炮为有效载荷的航天器在完成清除碎片任务时的关键技术。     

Evaluation of SARAL/AltiKa performance using GNSS/IMU equipped buoy in Sajafi,Imam Hassan and Kangan Ports

Performance of SARAL/AltiKa mission has been evaluated within 2016 altimeter calibration/validation framework in Persian Gulf through three campaigns conducted in the offshore waters of Sajafi, Imam Hassan and Kangan Ports, while the altimeter overflew the passes 470, 111 and 25 on 13 Feb, 7 March and 17 June 2016, respectively. As the preparation, a lightweight buoy was equipped with a GNSS receiver/choke-ring antenna and a MEMS-based IMU to measure independent datasets in the field operations. To obtain accurate sea surface height (SSH) time series, the offset of the onboard antenna from the equilibrium sea level was predetermined through surveying operations as the buoy was deploying in the onshore waters of Kangan Port. Accordingly, the double-difference carrier phase observations have been processed via the Bernese GPS Software v. 5.0 so as to provide the GNSS-derived time series at the comparison points of the calibration campaigns, once the disturbing effects due to the platform tilt and heave have been eliminated. Owing to comparing of the SSH time series and the associating altimetry 1?Hz GDR-T datasets, the calibration/validation of the SARAL/AltiKa has been performed in the both cases of radiometer and ECMWF wet troposphere corrections so as to identify potential land contamination. An agreement of the present findings in comparison with those attained in other international calibrations sites confirms the promising feasibility of Persian Gulf as a new dedicated site for calibration/validation of ongoing and future altimetry missions.     

Assessment of between-floor structural and topological properties on cognitive map development in multilevel built environments

The present study investigated cognitive map development in multilevel built environments. Three experiments were conducted in complex virtual buildings to examine the effects of five between-floor structural factors that may impede the accuracy of humans’ ability to build multilevel cognitive maps. Results from Experiments 1 and 2 (of three experiments) revealed that difficulties in developing multilevel cognitive maps are not solely caused by the z-axis offset, as is suggested in the literature, but are due to the factorial combination of a between-floor overlap and a z-axis offset. Results from Experiment 2 showed that this process becomes substantially more difficult when the reference directions between different floors have an angular offset from each other. Finally, results from Experiment 3 demonstrated that confusing between-floor heading shifts in aligned buildings did not make it reliably harder to build multilevel cognitive maps. The implications of these findings are discussed in terms of theories of mental representations in multilayered three-dimensional spaces, as well as for architectural design.     

飞机液压系统柱塞泵热分析

随着飞机液压系统向高压化、大功率化方向发展，液压系统的发热及温升问题受到了广泛关注。柱塞泵作为液压系统中重要的能量转换装置，对液压系统的功率损失和温度有重大的影响，良好的柱塞泵的热分析对液压系统的热设计和温度控制有重要的意义。然而传统的柱塞泵热分析方法，如平均油温法、软件仿真法和热节点网络法，因不够准确、高效和简洁而不能满足现代飞机液压系统热分析和热设计的相关需求。本文针对飞机液压系统柱塞泵发热的相关问题，采用基于集总参数的热网络分析方法，建立了柱塞泵热网络模型，通过对柱塞泵不同工况下的仿真，验证了模型的有效性和准确性，为柱塞泵及液压系统的热分析提供了参考。     

Simulating planetary wave propagation to the upper atmosphere during stratospheric warming events at different mountain wave scenarios

Parameterization schemes of atmospheric normal modes (NMs) and orographic gravity waves (OGWs) have been implemented into the mechanistic Middle and Upper Atmosphere Model (MUAM) simulating atmospheric general circulation. Based on the 12-members ensemble of runs with the MUAM, a composite of the stratospheric warming (SW) has been constructed using the UK Met Office data as the lower boundary conditions. The simulation results show that OGW amplitudes increase at altitudes above 30 km in the Northern Hemisphere after the SW event. At altitudes of about 50 km, OGWs have largest amplitudes over North American and European mountain systems before and during the composite SW, and over Himalayas after the SW. Simulations demonstrate substantial (up to 50–70%) variations of amplitudes of stationary planetary waves (PWs) during and after the SW in the mesosphere-lower thermosphere of the Northern Hemisphere. Westward travelling NMs have amplitude maxima not only in the Northern, but also in the Southern Hemisphere, where these modes have waveguides in the middle and upper atmosphere. Simulated variations of PW and NM amplitudes correspond to changes in the mean zonal wind, EP-fluxes and wave refractive index at different phases of the composite SW events. Inclusion of the parameterization of OGW effects leads to decreases in amplitudes (up to 15%) of almost all SPWs before and after the SW event and their increase (up to 40–60%) after the SW in the stratosphere and mesosphere at middle and high northern latitudes. It is suggested that observed changes in NM amplitudes in the Southern Hemisphere during SW could be caused by divergence of increased southward EP-flux. This EP-flux increases due to OGW drag before SW and extends into the Southern Hemisphere.     

Comparison of vertical E × B drift velocities and ground-based magnetometer observations of DELTA H in the low latitude under geomagnetically disturbed conditions

In the present work, we analyzed the daytime vertical E × B drift velocities obtained from Jicamarca Unattended Long-term Ionosphere Atmosphere (JULIA) radar and ΔH component of geomagnetic field measured as the difference between the magnitudes of the horizontal (H) components between two magnetometers deployed at two different locations Jicamarca, and Piura in Peru for 22 geomagnetically disturbed events in which either SC has occurred or Dst_max < ?50 nT during the period 2006–2011. The ΔH component of geomagnetic field is measured as the differences in the magnitudes of horizontal H component between magnetometer placed directly on the magnetic equator and one displaced 6–9° away. It will provide a direct measure of the daytime electrojet current, due to the eastward electric field. This will in turn gives the magnitude of vertical E × B drift velocity in the F region. A positive correlation exists between peak values of daytime vertical E × B drift velocity and peak value of ΔH for the three consecutive days of the events. It was observed that 45% of the events have daytime vertical E × B drift velocity peak in the magnitude range 10–20 m/s and 20–30 m/s and 20% have peak ΔH in the magnitude range 50–60 nT and 80–90 nT. It was observed that the time of occurrence of the peak value of both the vertical E × B drift velocity and the ΔH have a maximum (40%) probability in the same time range 11:00–13:00 LT. We also investigated the correlation between E × B drift velocity and D_st index and the correlation between delta H and D_st index. A strong positive correlation is found between E × B drift and D_st index as well as between delta H and D_st Index. Three different techniques of data analysis – linear, polynomial (order 2), and polynomial (order 3) regression analysis were considered. The regression parameters in all the three cases were calculated using the Least Square Method (LSM), using the daytime vertical E × B drift velocity and ΔH. A formula was developed which indicates the relationship between daytime vertical E × B drift velocity and ΔH, for the disturbed periods. The E × B drift velocity was then evaluated using the formulae thus found for the three regression analysis and validated for the ‘disturbed periods’ of 3 selected events. The E × B drift velocities estimated by the three regression analysis have a fairly good agreement with JULIA radar observed values under different seasons and solar activity conditions. Root Mean Square (RMS) errors calculated for each case suggest that polynomial (order 3) regression analysis provides a better agreement with the observations from among the three.     

Geometric error analysis of an over-constrained parallel tracking mechanism using the screw theory

This paper deals with geometric error modeling and sensitivity analysis of an overconstrained parallel tracking mechanism. The main contribution is the consideration of overconstrained features that are usually ignored in previous research. The reciprocal property between a motion and a force is applied to tackle this problem in the framework of the screw theory. First of all, a nominal kinematic model of the parallel tracking mechanism is formulated. On this basis, the actual twist of the moving platform is computed through the superposition of the joint twist and geometric errors. The actuation and constrained wrenches of each limb are applied to exclude the joint displacement. After eliminating repeated errors brought by the multiplication of wrenches, a geometric error model of the parallel tracking mechanism is built. Furthermore,two sensitivity indices are defined to select essential geometric errors for future kinematic calibration. Finally, the geometric error model with minimum geometric errors is verified by simulation with SolidWorks software. Two typical poses of the parallel tracking mechanism are selected, and the differences between simulation and calculation results are very small. The results confirm the correctness and accuracy of the geometric error modeling method for over-constrained parallel mechanisms.     

飞秒激光系统图像调焦装置以及方法

飞秒激光直写技术在复杂三维微结构加工领域具有显著优势，而调焦是否精准直接影响了所加工结构的完整度.提出了在光路中临时置入调焦光源和物的图像调焦技术，通过调节物的位置使其成像面与激光聚焦面一致，从而通过清晰可分辨的成像状态间接反映激光聚焦状态.利用Zemax软件模拟分析了原飞秒激光光路与加入调焦光源和物的调焦光路，二者可实现相同加工物镜后工作距离与良好成像质量，证明了该方法的可行性.通过分析得到该过程的成像误差主要由成像镜头焦深(3.9 μm)引起，我们获得的理想调焦精度可达到1/2焦深以内.设计了单层高度为5 μm的二层圆柱结构，通过多次实验验证了所加工元件高度误差在1.5 μm范围以内，与理论分析一致，满足飞秒激光系统的调焦要求.     

ORB-SLAM系统优化框架分析概述

首先阐述了ORB-SLAM系统的核心思想和基本框架,介绍了SLAM系统中光束平差法的应用实现,然后针对视觉里程计部分不同的关键帧位姿优化过程分别进行了详细阐述,并利用KITTI数据集的不同序列的实验结果进行比较研究,给出了核心的光束平差法在ORB-SLAM中的具体工作方式及性能分析,最后讨论和分析了ORB-SLAM的优势和不足。